| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| The Bluetooth Link Layer control procedure code in subsys/bluetooth/controller/ll_sw/ull_llcp_conn_upd.c retains the received RX node while a Connection Update / Connection Parameter procedure waits for its instant, so the node can later carry the host notification (llcp_rx_node_retain(), which marks it NODE_RX_TYPE_RETAIN and thereby suppresses the normal recycling in ull.c). The default: arm of llcp_rp_cu_rx() and llcp_lp_cu_rx() — the "invalid PDU, terminate the connection" path — completed the procedure without releasing that retained node. llcp_rr_check_done() then dequeued and freed the procedure context with ctx->node_ref.rx still pointing at the retained node, dropping the last reference to it.
A peer device in radio range can reach this without pairing, bonding, or encryption. Against a peripheral, the peer sends a well-formed LL_CONNECTION_UPDATE_IND with an instant a few connection events in the future (the node is retained and the procedure enters RP_CU_STATE_WAIT_INSTANT), then, before the instant is reached, sends any other LL Control PDU such as LL_LENGTH_REQ. ull_cp_rx() routes that PDU into the active remote Connection Update procedure, which takes the invalid-PDU path. The central role is reachable symmetrically after accepting an LL_CONNECTION_PARAM_REQ, and the local-procedure variant is reachable with LL_REJECT_IND.
With CONFIG_BT_CTLR_ASSERT_DEBUG enabled (its default), the resulting state violates the invariant asserted in llcp_rr_check_done(), so the two-PDU sequence produces an immediate fatal error in the controller. With those asserts disabled, each occurrence permanently loses one node from the controller's small fixed RX pool (sized from CONFIG_BT_CTLR_RX_BUFFERS, which defaults to 1); repeating the sequence across reconnections exhausts the pool, after which the link-layer receive path operates on a NULL node. The impact is an unauthenticated, remotely triggerable denial of service persisting until reboot; there is no memory-disclosure or memory-corruption consequence, since the leaked node simply becomes unreachable. |
| The Link Layer Control Procedure (LLCP) implementation of the Zephyr software Bluetooth LE Controller retains the receive node that carried an accepted LL_PHY_UPDATE_IND so that it can later be reused for the host notification when the update instant is reached (llcp_rx_node_retain() in subsys/bluetooth/controller/ll_sw/ull_llcp.c, and the node is deliberately not recycled while marked NODE_RX_TYPE_RETAIN). The invalid-PDU arms of llcp_lp_pu_rx() and llcp_rp_pu_rx() in subsys/bluetooth/controller/ll_sw/ull_llcp_phy.c completed the procedure via llcp_lr_complete() / llcp_rr_complete() without first releasing that retained node, so the procedure context — the only remaining reference to the node — was freed while the node was still held out of the receive pool.
A peer device on an established LE connection can drive this deterministically and without pairing or encryption. Against a peripheral it sends LL_PHY_REQ, receives LL_PHY_RSP, sends a valid LL_PHY_UPDATE_IND with an instant a few connection events in the future (so the node becomes retained), and then, before the instant is reached, sends any other LL Control PDU such as LL_LENGTH_REQ; ull_cp_rx() routes it to the active remote PHY Update procedure, which takes the invalid-PDU path. The mirror case applies to a locally initiated PHY Update followed by an LL_REJECT_IND.
In the default configuration (CONFIG_BT_ASSERT and CONFIG_BT_CTLR_ASSERT_DEBUG both default y) the violated invariant in llcp_lr_check_done() / llcp_rr_check_done() triggers a controller assertion, ending in k_oops() (or k_panic()) — a single crafted PDU sequence from radio range faults the device. With those assertions compiled out, each attempt silently leaks one receive PDU node and its memq link; because the controller receive pool is small (PDU_RX_CNT, driven by CONFIG_BT_CTLR_RX_BUFFERS, which defaults to 1) and each attempt costs the attacker only a reconnect, a few repetitions exhaust the pool and leave Bluetooth inoperable until reboot. On releases v3.4.0 through v3.7.x the assertion is never reached, whatever the configuration, so every attempt leaks silently.
The impact is limited to availability: the orphaned node leaves no dangling pointer that is later dereferenced and is never delivered to the host, so there is no memory corruption or information disclosure. The same pull request applies the identical release to the Connection Update and CIS-create procedures, whose invalid-PDU arms had the same omission. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/shrinker: Take a runtime PM ref before shrinking non-system memory
__xe_shrinker_walk() walks the SYSTEM and TT LRUs without a runtime PM
reference. Shrinking a bo outside system memory invalidates its GPU
mappings, which needs the device resumed, so while it is runtime
suspended the page table zap trips an assert and the TLB invalidation
returns -ENODEV:
WARNING: drivers/gpu/drm/xe/xe_bo.c:770 at xe_bo_move_notify+0x1fc/0x450 [xe]
xe_bo_shrink+0x20f/0x2b0 [xe]
__xe_shrinker_walk+0x174/0x410 [xe]
xe_shrinker_scan+0x10c/0x1e0 [xe]
do_shrink_slab+0x176/0x7e0
drop_caches_sysctl_handler+0x9c/0xf0
Take a reference before walking a memory type other than XE_PL_SYSTEM
and stop there if it cannot be acquired. Reuse the shrinker's existing
acquire path, which resumes the device directly where reclaim allows
that and otherwise queues the PM worker for a later scan. Stop the walk
once the scan target is met, so a satisfied scan does not wake the
device. System memory is still reclaimed while the device is suspended.
Gate this on xe_device_is_l2_flush_optimized(), the same condition under
which xe_bo_trigger_rebind() issues the invalidation for a non-fault-mode
vm, so reclaim is unaffected elsewhere. The System CCS copy already has
its own reference in xe_bo_shrink().
Only a non-fault-mode vm can reach this, since a fault-mode vm requires
LR mode and that holds a runtime PM reference for the vm's lifetime.
Reproduced with igt@xe_madvise@dontneed-before-exec while the GPU is
runtime suspended.
v2: simplify needs_rpm check. (Matt)
retarget Fixes tag since the issue occurs with the non-fault-mode
path added by 4e7ebff69aed.
v3: handle this in xe_shrinker.c instead of xe_bo.c (Thomas)
v4: stop the walk once the scan target is met. (Sashiko)
v5: rebase on the freed page accounting fix. (Sashiko)
v6: reuse the shrinker acquire path so runtime pm can be resumed
directly instead of always queueing a worker. (Thomas)
v7: replace xe_pm_runtime_put() with xe_shrinker_runtime_pm_put(). (Thomas)
(cherry picked from commit 628f92b28bf4c371c10207daf6fc4caee0c0db2e) |
| Navigating to a certain URL on the switch’s web server causes the switch to reboot. This can be automated using a tool like curl to create DoS conditions where the switch constantly reboots. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: don't allow injecting frames wider than the chanctx
Frames injected on a monitor interface can carry a radiotap
field requesting a bandwidth, which mac80211 passes down to
the driver regardless of the the actual operational bandwidth.
If the bandwidth requested is too wide, that triggers a warning
in hwsim:
WARN_ON(hwsim_get_chanwidth(bw) > hwsim_get_chanwidth(confbw))
Drop such frames entirely instead since they cannot be sent. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: unlist vifs when their netdev is unregistered
mac80211 only removes vifs from the local->interfaces list when
an interface is removed via ieee80211_if_remove(), before it
unregisters the netdev. However, it's possible for a netdev to
be unregistered without going through that: When the netns that
holds the wiphy is destroyed, the wiphy is supposed to move to
the init_ns, but that can run into allocation failures.
Then, mac80211 has an interface listed that doesn't exist, and
will eventually hit
BUG: failure at net/wireless/core.h:141/wiphy_to_rdev()!
...
_cfg80211_unregister_wdev+0x24/0x36a [cfg80211]
cfg80211_unregister_wdev+0x15/0x1d [cfg80211]
ieee80211_remove_interfaces+0x1ff/0x257 [mac80211]
ieee80211_unregister_hw+0x73/0x1d1 [mac80211]
mac80211_hwsim_del_radio+0x114/0x166 [mac80211_hwsim]
Remove the interface from the list in ->ndo_uninit if it's still
around to avoid this. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: don't filter by BSS type when removing stale entries
When an assoc AP switches to a channel that already has a BSS entry,
cfg80211_update_assoc_bss_entry() removes that entry before rehashing
the real one, since the two would otherwise collide in the BSS rbtree.
The lookup for that entry also required it to match the connection's BSS
type, so an entry advertising e.g. the IBSS capability bit was left in
place, and the following cfg80211_rehash_bss() then ran into it:
WARN_ON(!cmp)
Changing the type shouldn't really happen, but can be triggered by a
rogue AP/device, so drop the check and remove any entries matching
the comparison. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: only group hidden BSSes with beacon entries
When a probe response for an unknown BSS comes in, __cfg80211_bss_update()
looks for an existing entry with the same BSSID and a hidden (zero-length
or NUL-filled) SSID, and if it finds one it groups them, using the beacon
IEs from the existing entry.
But that could find another entry without a beacon, if it was also from a
probe response (with SSID), so there's a group without beacon elements.
If a beacon with a hidden SSID for that BSSID arrives later,
cfg80211_combine_bsses() goes looking for the probe response entries that
belong to it - i.e. entries with the same BSSID and channel that have no
beacon IEs - and finds those two. They are already grouped with each
other, so it hits its
WARN_ON_ONCE(bss->pub.hidden_beacon_bss)
WARN_ON_ONCE(!list_empty(&bss->hidden_list))
which are there because an entry without beacon elements is not supposed
to be part of a group yet.
Only combine entries when a beacon was already received, ones that are
kept separate will be combined when a beacon arrives. |
| A reachable assertion in the illumos bhyve instruction emulator allows a guest to panic the host. When emulating a REP-prefixed MOVS or STOS instruction that accesses guest MMIO, vie_emulate_movs() and vie_emulate_stos() in usr/src/uts/intel/io/vmm/vmm_instruction_emul.c do not clear the VIES_REPEAT status flag on the final iteration. For MMIO regions emulated in the kernel (the local APIC, I/O APIC and HPET), the stale flag causes a VERIFY assertion in vie_advance_pc() to fail, and the host panics. A privileged user within a guest VM can issue a REP MOVS or REP STOS instruction against the local APIC page to cause a denial of service of the host and every other guest running on it. The flaw has existed since 2020 (illumos-gate commit e0c0d44e), and affects any illumos distribution prior to illumos-gate commit 696ecf8d. |
| RIOT is an open-source microcontroller operating system designed for Internet of Things devices and other embedded systems. From version 2023.07 through version 2026.07, nanocoap_fileserver callers in sys/net/application_layer/nanocoap/fileserver.c ignore a failure returned by _resp_init() when coap_build_reply() cannot fit a response header into the response buffer. A remote client can send a CoAP request with a sufficiently large extended token when nanocoap_token_ext is enabled, causing response initialization to fail while _get_file() or _get_directory() continues with stale response state. The path then reaches _calc_szx2() and its pdu->payload_len > reserve assertion, terminating the affected service or device task. No fixed release is available as of this review. |
| named in ISC BIND 9.x before 9.9.7-P2 and 9.10.x before 9.10.2-P3 allows remote attackers to cause a denial of service (REQUIRE assertion failure and daemon exit) via TKEY queries. |
| Open5GS through 2.8.0 contains a reachable assertion vulnerability in mme_gn_handle_sgsn_context_request() that allows remote unauthenticated attackers to crash the MME via malformed SGSN Address IEs. Attackers sending GTPv1-C traffic from a configured SGSN address with a known UE IMSI or P-TMSI can supply an invalid address length to terminate open5gs-mmed, denying service to all subscribers. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: icmp: reject RTN_UNREACHABLE input routes in icmp_route_lookup
When the forward output route cannot be used in icmp_route_lookup(),
it enters the "reverse path" and calls ip_route_input() on fl4_dec.daddr,
the original packet's source address.
ip_route_input() only returns an error for truly invalid packets. For
unreachable addresses it will succeed and return an input route whose
dst.output is set to ip_rt_bug(). The existing check only rejects
RTN_LOCAL routes, so the RTN_UNREACHABLE route types can still be returned
and later used for output, syzkaller triggering a WARN_ON_ONCE()
in ip_rt_bug() as bellow:
------------[ cut here ]------------
WARNING: net/ipv4/route.c:1273 at ip_rt_bug+0x14/0x20
RIP: 0010:ip_rt_bug+0x14/0x20
Call Trace:
ip_push_pending_frames+0xfa/0x100
__icmp_send+0x905/0xf10
ip_options_compile+0xc0/0xd0
ip_rcv_finish_core+0x321/0xae0
ip_rcv+0x1de/0x260
__netif_receive_skb_one_core+0x11a/0x130
netif_receive_skb+0x7b/0x260
tun_get_user+0x11bf/0x1c10
------------[ cut here ]------------
Reject input route that is RTN_UNREACHABLE to fix it. The net warning
is only printed for RTN_LOCAL, as RTN_UNREACHABLE is not the result of
a race condition. |
| This CVE ID has been rejected as a duplicate. |
| In Modem, there is a possible system crash due to improper input validation. This could lead to remote denial of service, if a UE has connected to a rogue base station controlled by the attacker, with no additional execution privileges needed. User interaction is not needed for exploitation. Patch ID: MOLY01870473 / MOLY00814393; Issue ID: MSV-9041. |
| In the Linux kernel, the following vulnerability has been resolved:
bridge: Fix sleep in atomic context in netlink path
Since the introduction of the netlink configuration path for bridge
ports in commit 25c71c75ac87 ("bridge: bridge port parameters over
netlink"), br_setport() was always called with the bridge lock held
around it. Back then this decision made sense: The bridge lock protects
the STP state of the bridge and its ports and at that time the function
only processed three STP related netlink attributes (cost, priority and
state).
Nowadays, br_setport() processes a lot more attributes and most of them
do not need the bridge lock:
* Bridge flags: Only require RTNL. Read locklessly by the data path.
Annotations can be added in net-next.
* FDB port flushing: Only requires the FDB lock.
* Multicast attributes: Only require the multicast lock.
* Group forward mask: Only requires RTNL. Read locklessly by the data
path. Annotations can be added in net-next.
* Backup port and NHID: Only require RTNL. Read locklessly by the data
path.
This is a problem as the bridge calls dev_set_promiscuity() when certain
bridge port flags change and this function can sleep since the commit
cited below, resulting in a splat such as [1].
Fix this by reducing the scope of the bridge lock and only take it when
processing the three STP related attributes that require it. This is
consistent with the multicast attributes where each attribute acquires
the multicast lock instead of having one critical section for all
relevant attributes.
[1]
BUG: sleeping function called from invalid context at net/core/dev_addr_lists.c:1262
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 356, name: bridge
preempt_count: 201, expected: 0
RCU nest depth: 0, expected: 0
2 locks held by bridge/356:
#0: ffffffff919473a0 (rtnl_mutex){+.+.}-{4:4}, at: rtnetlink_rcv_msg (net/core/rtnetlink.c:80 net/core/rtnetlink.c:7002)
#1: ffff888115072d58 (&br->lock){+...}-{3:3}, at: br_setlink (./include/linux/spinlock.h:348 net/bridge/br_netlink.c:1117)
Preemption disabled at:
0x0
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:94 lib/dump_stack.c:120)
__might_resched.cold (kernel/sched/core.c:9163)
netif_rx_mode_run (net/core/dev_addr_lists.c:1262)
netif_rx_mode_sync (net/core/dev_addr_lists.c:1428)
dev_set_promiscuity (net/core/dev_api.c:289)
br_manage_promisc (net/bridge/br_if.c:135 net/bridge/br_if.c:172)
br_port_flags_change (net/bridge/br_if.c:242 net/bridge/br_if.c:747)
br_setport (net/bridge/br_netlink.c:1000)
br_setlink (net/bridge/br_netlink.c:1118)
rtnl_bridge_setlink (net/core/rtnetlink.c:5572)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7005)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
netlink_unicast (net/netlink/af_netlink.c:1318 net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
__sock_sendmsg (net/socket.c:787 (discriminator 4) net/socket.c:802 (discriminator 4))
____sys_sendmsg (net/socket.c:2698)
___sys_sendmsg (net/socket.c:2752)
__sys_sendmsg (net/socket.c:2784)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) |
| vLLM is an inference and serving engine for large language models. Prior to 0.30.0, the /inference/v1/generate endpoint in the disaggregated scale-out path accepts caller-supplied tensors in the features.kwargs_data field, cache identifiers in the features.mm_hashes field, ranges in the features.mm_placeholders field, and wire-selected multimodal field processors without rebinding them to the active model renderer contract. Forged grid geometry, field types, or non-positive placeholder lengths can terminate the shared EngineCore; when an attacker knows or can induce a victim's content hash, forged cache hashes can poison or retrieve cross-request encoder-cache state; and dropped sparse placeholder masks can alter replayed transport semantics. This issue is fixed in version 0.30.0. |
| vLLM is an inference and serving engine for large language models. Prior to 0.28.0, the default mirrored multimodal LRU cache can commit a media hash in the frontend sender cache during multimodal rendering and before engine admission, while the engine receiver cache never receives the payload if that request is rejected. A later request reusing the same media hash causes MultiModalProcessorSenderCache to send no payload and MultiModalReceiverCache to reach an assertion with the message "Expected a cached item," producing a shared-service availability failure. This issue is fixed in version 0.28.0. |
| A reachable assertion vulnerability exists in the Matter SDK (connectedhomeip) before 1.4.2, specifically within the Level Control cluster's periodic server tick logic. When a MoveToLevel command is sent and immediately followed by a write of OperationMode=2 (in the Pump Configuration and Control cluster), the server tick function violates the assertion `currentLevel < maxLevel`, resulting in a crash. This can be exploited remotely without authentication to cause denial of service. Affected versions include 1.3 and 1.4 (commit ab3d5ae). |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do not force reloc root creation during qgroup_account_snapshot()
[BUG]
When running btrfs/252 with quota enabled through MKFS_OPTIONS="-O quota",
it has a high chance to trigger the following kernel warning and flips
the fs RO:
BTRFS info (device dm-2): relocating block group 30408704 flags metadata|dup
------------[ cut here ]------------
WARNING: fs/btrfs/extent-tree.c:879 at lookup_inline_extent_backref+0x74b/0x960 [btrfs], CPU#4: btrfs/2173
CPU: 4 UID: 0 PID: 2173 Comm: btrfs Not tainted 7.2.0-rc6-custom+ #457 PREEMPT(full) 3adc6528fb66f7a55fe1095385818e742f200aab
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022
RIP: 0010:lookup_inline_extent_backref+0x74b/0x960 [btrfs]
Call Trace:
<TASK>
insert_inline_extent_backref+0x7c/0x160 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
__btrfs_inc_extent_ref+0xa9/0x270 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
__btrfs_run_delayed_refs+0x4af/0x11c0 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
btrfs_run_delayed_refs+0x9d/0xf0 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
create_pending_snapshot+0x39d/0xf00 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
create_pending_snapshots+0x9b/0xc0 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
btrfs_commit_transaction+0x280/0xeb0 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
prepare_to_relocate+0x147/0x200 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
relocate_block_group+0x6b/0x5e0 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
btrfs_relocate_block_group+0x92c/0x2380 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
btrfs_relocate_chunk+0x3f/0x1a0 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
btrfs_balance+0xa2c/0x19c0 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
btrfs_ioctl+0x2839/0x2d30 [btrfs 32f09462c54d9c922fca74a3e4866f4aa7737b72]
__x64_sys_ioctl+0x416/0x9a0
do_syscall_64+0xe1/0x790
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
BTRFS info (device dm-2): leaf 4593991680 gen 233 total ptrs 175 free space 5953 owner 2
BTRFS info (device dm-2): refs 3 lock_owner 2173 current 2173
item 0 key (166772736 METADATA_ITEM 1) itemoff 16250 itemsize 33
extent refs 1 gen 222 flags 2
ref#0: tree block backref root 266
[ Skip the tree dump ]
item 174 key (263225344 METADATA_ITEM 0) itemoff 10328 itemsize 33
extent refs 1 gen 162 flags 258
ref#0: tree block backref root 267
BTRFS error (device dm-2): extent item not found for insert, bytenr 179847168 num_bytes 16384 parent 4594335744 root_objectid 273 owner 0 offset 0
BTRFS error (device dm-2): failed to run delayed ref for logical 179847168 num_bytes 16384 type 182 action 1 ref_mod 1: -117
[CAUSE]
The above error is showing that there is a tree reference to a metadata
extent that is no longer there.
With "ref_verify" mount option (requires CONFIG_BTRFS_DEBUG), there is
some extra debug output:
BTRFS error (device dm-2): dumping block entry [180961280 16384], num_refs 0, metadata 1, from disk 0
BTRFS error (device dm-2): root entry 256, num_refs 18446744073709551615
BTRFS error (device dm-2): root entry 273, num_refs 18446744073709551615
BTRFS error (device dm-2): Ref action 3, root 273, ref_root 273, parent 0, owner 0, offset 0, num_refs 1
btrfs_force_cow_block+0x129/0x7d0 [btrfs]
btrfs_cow_block+0x10a/0x250 [btrfs]
btrfs_search_slot+0x5eb/0xf40 [btrfs]
btrfs_insert_empty_items+0x3a/0x70 [btrfs]
insert_with_overflow+0x53/0x130 [btrfs]
btrfs_insert_dir_item+0x125/0x290 [btrfs]
btrfs_add_link+0xaa/0x410 [btrfs]
btrfs_rename+0x5ea/0xcd0 [btrfs]
btrfs_rename2+0x28/0x60 [btrfs]
vfs_rename+0x5b2/0xe10
filename_renameat2+0x244/0x430
__x64_sys_rename+0x48/0x70
do_syscall_64+0xe1/0x790
entry_SYSCALL_64_after_hwframe+0x4b/0x53
---truncated--- |
