| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: pm: ADD_ADDR rtx: fix potential data-race
This mptcp_pm_add_timer() helper is executed as a timer callback in
softirq context. To avoid any data races, the socket lock needs to be
held with bh_lock_sock().
If the socket is in use, retry again soon after, similar to what is done
with the keepalive timer. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-tcp: fix race between ICReq handling and queue teardown
nvmet_tcp_handle_icreq() updates queue->state after sending an
Initialization Connection Response (ICResp), but it does so without
serializing against target-side queue teardown.
If an NVMe/TCP host sends an Initialization Connection Request
(ICReq) and immediately closes the connection, target-side teardown
may start in softirq context before io_work drains the already
buffered ICReq. In that case, nvmet_tcp_schedule_release_queue()
sets queue->state to NVMET_TCP_Q_DISCONNECTING and drops the queue
reference under state_lock.
If io_work later processes that ICReq, nvmet_tcp_handle_icreq() can
still overwrite the state back to NVMET_TCP_Q_LIVE. That defeats the
DISCONNECTING-state guard in nvmet_tcp_schedule_release_queue() and
allows a later socket state change to re-enter teardown and issue a
second kref_put() on an already released queue.
The ICResp send failure path has the same problem. If teardown has
already moved the queue to DISCONNECTING, a send error can still
overwrite the state with NVMET_TCP_Q_FAILED, again reopening the
window for a second teardown path to drop the queue reference.
Fix this by serializing both post-send state transitions with
state_lock and bailing out if teardown has already started.
Use -ESHUTDOWN as an internal sentinel for that bail-out path rather
than propagating it as a transport error like -ECONNRESET. Keep
nvmet_tcp_socket_error() setting rcv_state to NVMET_TCP_RECV_ERR before
honoring that sentinel so receive-side parsing stays quiesced until the
existing release path completes. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Reject unknown opcodes before ICRC processing
Even after applying commit 7244491dab34 ("RDMA/rxe: Validate pad and ICRC
before payload_size() in rxe_rcv"), a single unauthenticated UDP packet
can still trigger panic. That patch handled payload_size() underflow only
for valid opcodes with short packets, not for packets carrying an unknown
opcode. The unknown-opcode OOB read described below predates that commit
and reaches back to the initial Soft RoCE driver.
The check added there reads
pkt->paylen < header_size(pkt) + bth_pad(pkt) + RXE_ICRC_SIZE
where header_size(pkt) expands to rxe_opcode[pkt->opcode].length. The
rxe_opcode[] array has 256 entries but is only populated for defined IB
opcodes; any other entry (for example opcode 0xff) is zero-initialized, so
length == 0 and the check degenerates to
pkt->paylen < 0 + bth_pad(pkt) + RXE_ICRC_SIZE
which does not constrain pkt->paylen enough. rxe_icrc_hdr() then computes
rxe_opcode[pkt->opcode].length - RXE_BTH_BYTES
which underflows when length == 0 and passes a huge value to rxe_crc32(),
causing an out-of-bounds read of the skb payload.
Reproduced on v7.0-rc7 with that fix applied, QEMU/KVM with
CONFIG_RDMA_RXE=y and CONFIG_KASAN=y, after
rdma link add rxe0 type rxe netdev eth0
A single 48-byte UDP packet to port 4791 with BTH opcode=0xff and
QPN=IB_MULTICAST_QPN triggers:
BUG: KASAN: slab-out-of-bounds in crc32_le+0x115/0x170
Read of size 1 at addr ...
The buggy address is located 0 bytes to the right of
allocated 704-byte region
Call Trace:
crc32_le+0x115/0x170
rxe_icrc_hdr.isra.0+0x226/0x300
rxe_icrc_check+0x13f/0x3a0
rxe_rcv+0x6e1/0x16e0
rxe_udp_encap_recv+0x20a/0x320
udp_queue_rcv_one_skb+0x7ed/0x12c0
Subsequent packets with the same shape fault on unmapped memory and panic
the kernel. The trigger requires only module load and "rdma link add"; no
QP, no connection, and no authentication.
Fix this by rejecting packets whose opcode has no rxe_opcode[] entry,
detected via the zero mask or zero length, before any length arithmetic
runs. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: remove station if connection prep fails
If connection preparation fails for MLO connections, then the
interface is completely reset to non-MLD. In this case, we must
not keep the station since it's related to the link of the vif
being removed. Delete an existing station. Any "new_sta" is
already being removed, so that doesn't need changes.
This fixes a use-after-free/double-free in debugfs if that's
enabled, because a vif going from MLD (and to MLD, but that's
not relevant here) recreates its entire debugfs. |
| In the Linux kernel, the following vulnerability has been resolved:
isofs: validate block number from NFS file handle in isofs_export_iget
isofs_fh_to_dentry() and isofs_fh_to_parent() pass an attacker-
controlled block number (ifid->block or ifid->parent_block) from
the NFS file handle to isofs_export_iget(), which only rejects
block == 0 before calling isofs_iget() and ultimately sb_bread().
A crafted file handle with fh_len sufficient to pass the check
added by commit 0405d4b63d08 ("isofs: Prevent the use of too small
fid") can still drive the server to read any in-range block on the
backing device as if it were an iso_directory_record. That earlier
fix was assigned CVE-2025-37780.
sb_bread() on an out-of-range block returns NULL cleanly via the
EIO path, so there is no memory-safety violation. For in-range
reads of adjacent-partition data on the same block device, the
unrelated bytes end up in iso_inode_info fields that reach the NFS
client as dentry metadata. The deployment surface (isofs exported
over NFS from loop-mounted images) is narrow and requires an
authenticated NFS peer, but the malformed-file-handle class is
reportable as hardening next to the existing CVE-2025-37780 fix.
Reject block >= ISOFS_SB(sb)->s_nzones in isofs_export_iget() so
the check covers both isofs_fh_to_dentry() and isofs_fh_to_parent()
call sites with a single line. |
| In the Linux kernel, the following vulnerability has been resolved:
ip6_gre: Use cached t->net in ip6erspan_changelink().
After commit 5e72ce3e3980 ("net: ipv6: Use link netns in newlink() of
rtnl_link_ops"), ip6erspan_newlink() correctly resolves the per-netns
ip6gre hash via link_net. ip6erspan_changelink() was not converted in
that series and still uses dev_net(dev), which diverges from the
device's creation netns after IFLA_NET_NS_FD migration.
This re-inserts the tunnel into the wrong per-netns hash. The
original netns keeps a stale entry. When that netns is later
destroyed, ip6gre_exit_rtnl_net() walks the stale entry, producing a
slab-use-after-free reported by KASAN, followed by a kernel BUG at
net/core/dev.c (LIST_POISON1) in unregister_netdevice_many_notify().
Reachable from an unprivileged user namespace (unshare --user
--map-root-user --net).
ip6gre_changelink() earlier in the same file already uses the cached
t->net; only ip6erspan_changelink() has the wrong shape. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: Fix slab-out-of-bounds access in auth message processing
If a (potentially corrupted) message of type CEPH_MSG_AUTH_REPLY
contains a positive value in its result field, it is treated as an
error code by ceph_handle_auth_reply() and returned to
handle_auth_reply(). Thereafter, an attempt is made to send the
preallocated message of type CEPH_MSG_AUTH, where the returned value is
interpreted as the size of the front segment to send. If the result
value in the message is greater than the size of the memory buffer
allocated for the front segment, an out-of-bounds access occurs, and
the content of the memory region beyond this buffer is sent out.
This patch fixes the issue by treating only negative values in the
result field as errors. Positive values are therefore treated as success
in the same way as a zero value. Additionally, a BUG_ON is added to
__send_prepared_auth_request() comparing the len parameter to
front_alloc_len to prevent sending the message if it exceeds the bounds
of the allocation and to make it easier to catch any logic flaws leading
to this. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mana: Remove user triggerable WARN_ON() in mana_ib_create_qp_rss()
Sashiko points out that the user can specify WQs sharing the same CQ as a
part of the uAPI and this will trigger the WARN_ON() then go on to corrupt
the kernel.
Just reject it outright and fail the QP creation. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: defensively unhash xfrm_state lists in __xfrm_state_delete
KASAN reproduces a slab-use-after-free in __xfrm_state_delete()'s
hlist_del_rcu calls under syzkaller load on linux-6.12.y stable
(reproduced on 6.12.47, also reachable via the same code path on
torvalds/master and on the ipsec tree). Nine unique signatures cluster
in the xfrm_state lifecycle, the load-bearing one being:
BUG: KASAN: slab-use-after-free in __hlist_del include/linux/list.h:990 [inline]
BUG: KASAN: slab-use-after-free in hlist_del_rcu include/linux/rculist.h:516 [inline]
BUG: KASAN: slab-use-after-free in __xfrm_state_delete net/xfrm/xfrm_state.c
Write of size 8 at addr ffff8881198bcb70 by task kworker/u8:9/435
Workqueue: netns cleanup_net
Call Trace:
__hlist_del / hlist_del_rcu
__xfrm_state_delete
xfrm_state_delete
xfrm_state_flush
xfrm_state_fini
ops_exit_list
cleanup_net
The other observed signatures hit the same slab object from
__xfrm_state_lookup, xfrm_alloc_spi, __xfrm_state_insert and an OOB
write variant of __xfrm_state_delete, all on the byseq/byspi
hash chains.
__xfrm_state_delete() guards its byseq and byspi unhashes with
value-based predicates:
if (x->km.seq)
hlist_del_rcu(&x->byseq);
if (x->id.spi)
hlist_del_rcu(&x->byspi);
while everywhere else in the file (e.g. state_cache, state_cache_input)
the safer hlist_unhashed() check is used. xfrm_alloc_spi() sets
x->id.spi = newspi inside xfrm_state_lock and then immediately inserts
into byspi, but a path that observes x->id.spi != 0 outside of
xfrm_state_lock can still skip-or-hit the byspi unhash inconsistently
with whether x is actually on the list. The same holds for x->km.seq
versus byseq, and the bydst/bysrc unhashes have no predicate at all,
so a second __xfrm_state_delete() on the same object writes through
LIST_POISON pprev.
The defensive change here:
- Use hlist_del_init_rcu() instead of hlist_del_rcu() on bydst,
bysrc, byseq and byspi so a second deletion is a no-op rather
than a write through LIST_POISON pprev. The byseq/byspi nodes
are already initialised in xfrm_state_alloc().
- Test hlist_unhashed() rather than the value predicate for
byseq/byspi, so the unhash decision tracks list state rather than
mutable scalar fields.
Empirical verification: applied this patch on top of v6.12.47, rebuilt,
and re-ran the same syzkaller harness for 1h16m on a previously-crashy
configuration that produced ~100 hits each of slab-use-after-free
Read in xfrm_alloc_spi / Read in __xfrm_state_lookup / Write in
__xfrm_state_delete. After the patch, 7.1M execs across 32 VMs at
~1550 exec/sec produced zero xfrm_state UAF/OOB hits. /proc/slabinfo
confirms the xfrm_state slab is actively allocated and freed during
the run (~143 KiB resident), so the fuzzer is still exercising those
code paths -- they just no longer crash.
Reproduction:
- Linux 6.12.47 x86_64 + KASAN_GENERIC + KASAN_INLINE + KCOV
- syzkaller @ 746545b8b1e4c3a128db8652b340d3df90ce61db
- 32 QEMU/KVM VMs x 2 vCPU on AWS c5.metal bare metal
- 9 unique signatures collected in ~9h, all within xfrm_state
lifecycle |
| In the Linux kernel, the following vulnerability has been resolved:
block: add pgmap check to biovec_phys_mergeable
biovec_phys_mergeable() is used by the request merge, DMA mapping,
and integrity merge paths to decide if two physically contiguous
bvec segments can be coalesced into one. It currently has no check
for whether the segments belong to different dev_pagemaps.
When zone device memory is registered in multiple chunks, each chunk
gets its own dev_pagemap. A single bio can legitimately contain
bvecs from different pgmaps -- iov_iter_extract_bvecs() breaks at
pgmap boundaries but the outer loop in bio_iov_iter_get_pages()
continues filling the same bio. If such bvecs are physically
contiguous, biovec_phys_mergeable() will coalesce them, making it
impossible to recover the correct pgmap for the merged segment
via page_pgmap().
Add a zone_device_pages_have_same_pgmap() check to prevent merging
bvec segments that span different pgmaps. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Reject non-8-byte ATOMIC_WRITE payloads
atomic_write_reply() at drivers/infiniband/sw/rxe/rxe_resp.c
unconditionally dereferences 8 bytes at payload_addr(pkt):
value = *(u64 *)payload_addr(pkt);
check_rkey() previously accepted an ATOMIC_WRITE request with pktlen ==
resid == 0 because the length validation only compared pktlen against
resid. A remote initiator that sets the RETH length to 0 therefore reaches
atomic_write_reply() with a zero-byte logical payload, and the responder
reads sizeof(u64) bytes from past the logical end of the packet into
skb->head tailroom, then writes those 8 bytes into the attacker's MR via
rxe_mr_do_atomic_write(). That is a remote disclosure of 4 bytes of kernel
tailroom per probe (the other 4 bytes are the packet's own trailing ICRC).
IBA oA19-28 defines ATOMIC_WRITE as exactly 8 bytes. Anything else is
protocol-invalid. Hoist a strict length check into check_rkey() so the
responder never reaches the unchecked dereference, and keep the existing
WRITE-family length logic for the normal RDMA WRITE path.
Reproduced on mainline with an unmodified rxe driver: a sustained
zero-length ATOMIC_WRITE probe repeatedly leaks adjacent skb head-buffer
bytes into the attacker's MR, including recognisable kernel strings and
partial kernel-direct-map pointer words. With this patch applied the
responder rejects the PDU and the MR stays all-zero. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Fix shadow paging use-after-free due to unexpected GFN
The shadow MMU computes GFNs for direct shadow pages using sp->gfn plus
the SPTE index. This assumption breaks for shadow paging if the guest
page tables are modified between VM entries (similar to commit
aad885e77496, "KVM: x86/mmu: Drop/zap existing present SPTE even
when creating an MMIO SPTE", 2026-03-27). The flow is as follows:
- a PDE is installed for a 2MB mapping, and a page in that area is
accessed. KVM creates a kvm_mmu_page consisting of 512 4KB pages;
the kvm_mmu_page is marked by FNAME(fetch) as direct-mapped because
the guest's mapping is a huge page (and thus contiguous).
- the PDE mapping is changed from outside the guest.
- the guest accesses another page in the same 2MB area. KVM installs
a new leaf SPTE and rmap entry; the SPTE uses the "correct" GFN
(i.e. based on the new mapping, as changed in the previous step) but
that GFN is outside of the [sp->gfn, sp->gfn + 511] range; therefore
the rmap entry cannot be found and removed when the kvm_mmu_page
is zapped.
- the memslot that covers the first 2MB mapping is deleted, and the
kvm_mmu_page for the now-invalid GPA is zapped. However, rmap_remove()
only looks at the [sp->gfn, sp->gfn + 511] range established in step 1,
and fails to find the rmap entry that was recorded by step 3.
- any operation that causes an rmap walk for the same page accessed
by step 3 then walks a stale rmap and dereferences a freed kvm_mmu_page.
This includes dirty logging or MMU notifier invalidations (e.g., from
MADV_DONTNEED).
The underlying issue is that KVM's walking of shadow PTEs assumes that
if a SPTE is present when KVM wants to install a non-leaf SPTE, then the
existing kvm_mmu_page must be for the correct gfn. Because the only way
for the gfn to be wrong is if KVM messed up and failed to zap a SPTE...
which shouldn't happen, but *actually* only happens in response to a
guest write.
That bug dates back literally forever, as even the first version of KVM
assumes that the GFN matches and walks into the "wrong" shadow page.
However, that was only an imprecision until 2032a93d66fa ("KVM: MMU:
Don't allocate gfns page for direct mmu pages") came along.
Fix it by checking for a target gfn mismatch and zapping the existing
SPTE. That way the old SP and rmap entries are gone, KVM installs
the rmap in the right location, and everyone is happy. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_conn: fix potential UAF in create_big_sync
Add hci_conn_valid() check in create_big_sync() to detect stale
connections before proceeding with BIG creation. Handle the
resulting -ECANCELED in create_big_complete() and re-validate the
connection under hci_dev_lock() before dereferencing, matching the
pattern used by create_le_conn_complete() and create_pa_complete().
Keep the hci_conn object alive across the async boundary by taking
a reference via hci_conn_get() when queueing create_big_sync(), and
dropping it in the completion callback. The refcount and the lock
are complementary: the refcount keeps the object allocated, while
hci_dev_lock() serializes hci_conn_hash_del()'s list_del_rcu() on
hdev->conn_hash, as required by hci_conn_del().
hci_conn_put() is called outside hci_dev_unlock() so the final put
(which resolves to kfree() via bt_link_release) does not run under
hdev->lock, though the release path would be safe either way.
Without this, create_big_complete() would unconditionally
dereference the conn pointer on error, causing a use-after-free
via hci_connect_cfm() and hci_conn_del(). |
| In the Linux kernel, the following vulnerability has been resolved:
dm-thin: fix metadata refcount underflow
There's a bug in dm-thin in the function rebalance_children. If the
internal btree node has one entry, the code tries to copy all btree
entries from the node's child to the node itself and then decrement the
child's reference count.
If the child node is shared (it has reference count > 1), we won't free
it, so there would be two pointers to each of the grandchildren nodes.
But the reference counts of the grandchildren is not increased, thus the
reference count doesn't match the number of pointers that point to the
grandchildren. This results in "device mapper: space map common: unable
to decrement block" errors.
Fix this bug by incrementing reference counts on the grandchildren if the
btree node is shared. |
| In the Linux kernel, the following vulnerability has been resolved:
net: strparser: fix skb_head leak in strp_abort_strp()
When the stream parser is aborted, for example after a message assembly timeout,
it can still hold a reference to a partially assembled message in
strp->skb_head.
That skb is not released in strp_abort_strp(), which leaks the partially
assembled message and can be triggered repeatedly to exhaust memory.
Fix this by freeing strp->skb_head and resetting the parser state in the
abort path. Leave strp_stop() unchanged so final cleanup still happens in
strp_done() after the work and timer have been synchronized. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipv6: fix NOREF dst use in seg6 and rpl lwtunnels
seg6_input_core() and rpl_input() call ip6_route_input() which sets a
NOREF dst on the skb, then pass it to dst_cache_set_ip6() invoking
dst_hold() unconditionally.
On PREEMPT_RT, ksoftirqd is preemptible and a higher-priority task can
release the underlying pcpu_rt between the lookup and the caching
through a concurrent FIB lookup on a shared nexthop.
Simplified race sequence:
ksoftirqd/X higher-prio task (same CPU X)
----------- --------------------------------
seg6_input_core(,skb)/rpl_input(skb)
dst_cache_get()
-> miss
ip6_route_input(skb)
-> ip6_pol_route(,skb,flags)
[RT6_LOOKUP_F_DST_NOREF in flags]
-> FIB lookup resolves fib6_nh
[nhid=N route]
-> rt6_make_pcpu_route()
[creates pcpu_rt, refcount=1]
pcpu_rt->sernum = fib6_sernum
[fib6_sernum=W]
-> cmpxchg(fib6_nh.rt6i_pcpu,
NULL, pcpu_rt)
[slot was empty, store succeeds]
-> skb_dst_set_noref(skb, dst)
[dst is pcpu_rt, refcount still 1]
rt_genid_bump_ipv6()
-> bumps fib6_sernum
[fib6_sernum from W to Z]
ip6_route_output()
-> ip6_pol_route()
-> FIB lookup resolves fib6_nh
[nhid=N]
-> rt6_get_pcpu_route()
pcpu_rt->sernum != fib6_sernum
[W <> Z, stale]
-> prev = xchg(rt6i_pcpu, NULL)
-> dst_release(prev)
[prev is pcpu_rt,
refcount 1->0, dead]
dst = skb_dst(skb)
[dst is the dead pcpu_rt]
dst_cache_set_ip6(dst)
-> dst_hold() on dead dst
-> WARN / use-after-free
For the race to occur, ksoftirqd must be preemptible (PREEMPT_RT without
PREEMPT_RT_NEEDS_BH_LOCK) and a concurrent task must be able to release
the pcpu_rt. Shared nexthop objects provide such a path, as two routes
pointing to the same nhid share the same fib6_nh and its rt6i_pcpu
entry.
Fix seg6_input_core() and rpl_input() by calling skb_dst_force() after
ip6_route_input() to force the NOREF dst into a refcounted one before
caching.
The output path is not affected as ip6_route_output() already returns a
refcounted dst. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: aloop: Fix peer runtime UAF during format-change stop
loopback_check_format() may stop the capture side when playback starts
with parameters that no longer match a running capture stream. Commit
826af7fa62e3 ("ALSA: aloop: Fix racy access at PCM trigger") moved
the peer lookup under cable->lock, but the actual snd_pcm_stop() still
runs after dropping that lock.
A concurrent close can clear the capture entry from cable->streams[] and
detach or free its runtime while the playback trigger path still holds a
stale peer substream pointer.
Keep a per-cable count of in-flight peer stops before dropping
cable->lock, and make free_cable() wait for those stops before
detaching the runtime. This preserves the existing behavior while
making the peer runtime lifetime explicit. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix the out-of-bounds nameoff handling for trailing dirents
Currently we already have boundary-checks for nameoffs, but the trailing
dirents are special since the namelens are calculated with strnlen()
with unchecked nameoffs.
If a crafted EROFS has a trailing dirent with nameoff >= maxsize,
maxsize - nameoff can underflow, causing strnlen() to read past the
directory block.
nameoff0 should also be verified to be a multiple of
`sizeof(struct erofs_dirent)` as well [1].
[1] https://sashiko.dev/#/patchset/20260416063511.3173774-1-hsiangkao%40linux.alibaba.com |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nSVM: Raise #UD if unhandled VMMCALL isn't intercepted by L1
Explicitly synthesize a #UD for VMMCALL if L2 is active, L1 does NOT want
to intercept VMMCALL, nested_svm_l2_tlb_flush_enabled() is true, and the
hypercall is something other than one of the supported Hyper-V hypercalls.
When all of the above conditions are met, KVM will intercept VMMCALL but
never forward it to L1, i.e. will let L2 make hypercalls as if it were L1.
The TLFS says a whole lot of nothing about this scenario, so go with the
architectural behavior, which says that VMMCALL #UDs if it's not
intercepted.
Opportunistically do a 2-for-1 stub trade by stub-ifying the new API
instead of the helpers it uses. The last remaining "single" stub will
soon be dropped as well.
[sean: rewrite changelog and comment, tag for stable, remove defunct stubs] |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5: validate payload size before accessing journal metadata
r5c_recovery_analyze_meta_block() and
r5l_recovery_verify_data_checksum_for_mb() iterate over payloads in a
journal metadata block using on-disk payload size fields without
validating them against the remaining space in the metadata block.
A corrupted journal contains payload sizes extending beyond the PAGE_SIZE
boundary can cause out-of-bounds reads when accessing payload fields or
computing offsets.
Add bounds validation for each payload type to ensure the full payload
fits within meta_size before processing. |
