| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| phpMyFAQ from 4.2.0-alpha.2 before 4.2.0-beta lacks brute-force lockout in the removeTwofactorConfig() 2FA removal endpoint, allowing authenticated attackers to guess TOTP codes without limit. Attackers holding a hijacked session and CSRF token can repeatedly POST guesses to /api/user/remove-twofactor to permanently disable the victim's 2FA. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: trf7970a: power down on startup RX gain failure
trf7970a_startup() powers up the device before applying the optional RX
gain reduction. If the register read or write fails, it returns without
undoing that power-up. Probe's unwind only drops the separate regulator
references acquired by probe, leaving the additional VIN enable from
startup unbalanced. The system resume caller also has no power-down on
this error.
Call trf7970a_power_down() before returning the RX gain error to deassert
the enable GPIOs, release the startup VIN reference and restore the
powered-off state. Runtime PM has not been enabled yet, so the full
shutdown helper is not appropriate here. Preserve the original SPI error.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: drop truncated I/RR/RNR PDUs in nfc_llcp_recv_hdlc()
nfc_llcp_recv_hdlc() reads the sequence byte skb->data[2], via
nfc_llcp_ns()/nfc_llcp_nr(), before any length check. The receive path
only guarantees the two-byte LLCP header -- __nfc_llcp_recv() checks it
with pskb_may_pull() and nfc_llcp_recv_agf() admits two-byte inner PDUs
-- so a two-byte I, RR or RNR PDU reads one byte of uninitialised skb
tailroom. The byte becomes N(R)/N(S); a peer can already set those with
a well-formed PDU, so this is acting on uninitialised memory, not new
peer control.
Guard the read with pskb_may_pull(), as commit 95674f506c63 ("nfc: llcp:
reject PDUs shorter than the LLCP header") did for the two-byte header,
so the sequence byte is present and linear before it is read. RR and RNR
PDUs are LLCP_HEADER_SIZE + LLCP_SEQUENCE_SIZE bytes and an I PDU is
longer, so no valid frame is rejected; a truncated PDU is malformed, so
return without a DM reply. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: fix use-after-free in nfc_get_local_general_bytes
Commit 6709d4b7bc2e ("net: nfc: Fix use-after-free caused by
nfc_llcp_find_local") attempted to fix a use-after-free (UAF) issue by
invoking nfc_llcp_local_put(local) after accessing local->gb. However,
if the reference count drops to zero, local is freed immediately,
leading to a use-after-free when callers access the returned pointer.
Alternative approaches using dynamic allocation (e.g. kmemdup) introduced
memory leaks because callers consistently treat the returned pointer as
borrowed memory.
Fix this properly by refactoring nfc_llcp_general_bytes() and
nfc_get_local_general_bytes() to accept a caller-provided output buffer
(out_gb) and its maximum length (gb_max_len). The general bytes are
safely copied into out_gb before calling nfc_llcp_local_put(local),
ensuring safe lifetime management without ownership transfer complications.
Update all callers across drivers (microread, pn533, pn544, st21nfca,
digital_dep, and nci) to provide their own destination buffers and pass
them to nfc_get_local_general_bytes(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: mdb: restart port group walk after deletion
br_mdb_flush_pgs() keeps a pointer-to-pointer cursor while walking
mp->ports. br_multicast_del_pg() can re-enter the same MDB entry through
br_multicast_sg_del_exclude_ports() and unlink other port groups. If the
cursor points into one of those groups, the next iteration dereferences a
stale cursor and can leave mp->ports pointing at freed memory.
A following RTM_GETMDB exposes the dangling pointer:
BUG: KASAN: slab-use-after-free in br_mdb_dump
Read of size 8
br_mdb_dump
rtnl_mdb_dump
rtnl_dumpit
netlink_dump
Reset the cursor to mp->ports after every deletion. The deletion removes at
least the selected group, so the restarted walk always makes progress. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: conntrack: avoid modifying shared unconfirmed ct entry
In a case where skb with an unconfirmed ct entry gets cloned, we may
end up committing both but with different sets of extensions.
The series of events:
1. The first clone wants to commit and runs the helpers wiring up
the extension pointer into the expectation list.
2. Then it looses the confirmation keeping the entry unconfirmed.
3. Second clone now wants to commit labels and adds the new extension
for that breaking the pointer in the expectation list causing
UAF on the destruction path later.
While this is possible to trigger, there should be no practical
network pipeline where committing both clones without modifications
into the same zone is needed. So, let's just reset the entry in case
for some reason we got an skb with a shared one during commit. This
doesn't affect any known use cases, but avoids any potential problems
with sharing and modification of the unconfirmed ct entry.
The fixes tag points to the introduction of helpers, since that's the
main UAF trigger for the sharing. |
| In the Linux kernel, the following vulnerability has been resolved:
cgroup/cpuset: Return PERR_NOCPUS in remote_partition_enable() on subpartitions_cpus conflict
When a remote partition is created underneath an existing local partition
via a non-partition (PRS_MEMBER) intermediate cgroup, update_prstate() sees
parent->partition_root_state == PRS_MEMBER and calls
remote_partition_enable().
Commit 86888c7bd117 ("cgroup/cpuset: Add warnings to catch inconsistency
in exclusive CPUs") replaced the cpumask_intersects(tmp->new_cpus,
subpartitions_cpus) error check in remote_partition_enable() with
WARN_ON_ONCE(). As a result, remote_partition_enable() emits a warning
and proceeds to enable the remote partition on CPUs that are already
owned by the ancestor local partition in subpartitions_cpus.
This can be reproduced on Linux 7.3.0-rc3 with:
mkdir -p /tmp/cg1
mount -t cgroup2 none /tmp/cg1
echo "+cpuset" > /tmp/cg1/cgroup.subtree_control
mkdir /tmp/cg1/A
echo 1 > /tmp/cg1/A/cpuset.cpus
echo 1 > /tmp/cg1/A/cpuset.cpus.exclusive
echo root > /tmp/cg1/A/cpuset.cpus.partition
echo "+cpuset" > /tmp/cg1/A/cgroup.subtree_control
mkdir /tmp/cg1/A/B
echo 1 > /tmp/cg1/A/B/cpuset.cpus
echo 1 > /tmp/cg1/A/B/cpuset.cpus.exclusive
echo "+cpuset" > /tmp/cg1/A/B/cgroup.subtree_control
mkdir /tmp/cg1/A/B/D
echo 1 > /tmp/cg1/A/B/D/cpuset.cpus
echo 1 > /tmp/cg1/A/B/D/cpuset.cpus.exclusive
echo root > /tmp/cg1/A/B/D/cpuset.cpus.partition
which triggers:
WARNING: kernel/cgroup/cpuset.c:1594 at remote_partition_enable+0x1c1/0x300
and leaves both /tmp/cg1/A and /tmp/cg1/A/B/D as active root partitions
claiming exclusive CPU 1.
Fix this by returning PERR_NOCPUS when tmp->new_cpus intersects
subpartitions_cpus in remote_partition_enable(), matching the error code
used by remote_cpus_update() for the same subpartitions_cpus conflict, and
add a regression test case to
tools/testing/selftests/cgroup/test_cpuset_prs.sh.
Tested in QEMU on Linux 7.3.0-rc3 using the reproducer above and
tools/testing/selftests/cgroup/test_cpuset_prs.sh. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: replace bind when learning local endpoint
struct ovpn_bind is published through peer->bind with RCU, but local
endpoint learning updates bind->local in place under peer->lock. UDP TX
reads the field without that lock. In particular, a concurrent IPv6
update can therefore result in a torn address read.
Use ovpn_peer_reset_sockaddr to publish a replacement bind when learning
a new local endpoint, just as a remote endpoint change does. Preserve
the current remote address and reset the dst cache only after the new
bind has been published successfully.
Track remote endpoint changes separately so that float notification and
transport-address rehashing remain limited to actual peer floats. |
| In the Linux kernel, the following vulnerability has been resolved:
eth: fbnic: reset num_napi when the napi vectors are freed
fbn->num_napi is the count of live napi vectors, each of which owns an
IRQ. The PM path had freed them without clearing the count.
fbnic_pm_suspend() tears the datapath down via ndo_stop() and frees the
IRQs, but leaves netif_running() true so resume knows to re-open. Resume
rebuilds the datapath in __fbnic_pm_resume() and fbnic_reset_queues() sets
num_napi and __fbnic_open() re-allocates the vectors.
When the datapath is torn down but never rebuilt, num_napi is left
pointing at freed vectors under 2 different scenarios:
- a PCIe error recovery that fails (fbnic_err_slot_reset() ->
__fbnic_pm_resume() returns an error -> PCI_ERS_RESULT_DISCONNECT), so
.resume never runs; or
- an __fbnic_open() that fails partway on resume and unwinds, freeing
the vectors after fbnic_reset_queues() has already set num_napi.
The netdev is then running with num_napi > 0 but napi[] freed, and the
eventual remove/unbind close re-enters fbnic_down() -> fbnic_dbg_down()
and dereferences the freed vectors:
BUG: kernel NULL pointer dereference, address: 0000000000000210
RIP: fbnic_dbg_down+0x28
Clear num_napi when the vectors are freed: in the suspend teardown (a
good resume re-establishes it before __fbnic_open()) and on the resume
open failure. A redundant ndo_stop() then walks an empty napi[]. The
normal ndo_stop() down/up cycle is untouched and keeps num_napi for the
next ndo_open(). |
| In the Linux kernel, the following vulnerability has been resolved:
iio: imu: adis16400: fix unprotected debugfs reads
adis16400_serial_number_fops is open coded and never calls
debugfs_file_get(), so debugfs_remove_recursive() does not wait for a
read in progress and unbind frees the iio_dev underneath it.
Commit ae1d37a9bb4b ("iio: imu: adis16400: use DEFINE_DEBUGFS_ATTRIBUTE
instead of DEFINE_SIMPLE_ATTRIBUTE") converted product_id and
flash_count to DEFINE_DEBUGFS_ATTRIBUTE, which protects itself, but
moved all three files to debugfs_create_file_unsafe().
serial_number prints three registers as "%.4x-%.4x-%.4x" and
DEFINE_DEBUGFS_ATTRIBUTE() formats a single u64, so it cannot be
converted without changing what the file returns. adis16475 and
adis16550 already use debugfs_create_file() for their open coded
files. Use it here too. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: discard post-EOF pagecache when extending a file via clone range
cifs_remap_file_range() discarded the pagecache only for the folios
overlapping the destination region, so when a clone extends the file the
folio straddling the old EOF - which may hold data dirtied past EOF
through an mmap - was never dropped and became visible as file content
once the file was extended.
Start the discard at the smaller of fstart and the old EOF. i_size is
still old here, so nothing past the old EOF is flushed to the server. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/mediatek: Add missing IS_ERR check for ovl_adaptor platform device
platform_device_register_data() can fail and return an ERR_PTR, but the
return value is used without checking, leading to an invalid pointer
being stored in ddp_comp[].dev and passed to component_match_add() and
mtk_ddp_comp_init(), which could result in a kernel crash.
Add an IS_ERR() check to jump to the error handling path on failure. |
| During an upload, curl mishandles HTTP/2 `RST_STREAM` received from the server
(with reason `HTTP_1_1_REQUIRED` or `REFUSED_STREAM`) leading to a use after
free of a `struct Curl_easy` object. |
| A vulnerability was found in diem-project diem up to 5.1.3. This vulnerability affects unknown code of the file dmCorePlugin/lib/data/dmDataLoad.php. Performing a manipulation results in use of default password. The attack is possible to be carried out remotely. The exploit has been made public and could be used. It is suggested to update the configuration settings. The project was informed of the problem early through an issue report but has not responded yet. |
| In the Linux kernel, the following vulnerability has been resolved:
vlan: ensure sufficient headroom in vlan_dev_hard_header()
Callers that only reserve ETH_HLEN or less (such as llc_alloc_frame()),
or skbs allocated before dynamic device/headroom changes (e.g. toggling
VLAN_FLAG_REORDER_HDR or bonding/team switching slaves), can reach
vlan_dev_hard_header() with insufficient headroom and trigger
skb_under_panic().
Use skb_cow_head() in vlan_dev_hard_header() when VLAN_FLAG_REORDER_HDR
is not set to ensure sufficient headroom for the VLAN header(s) and the
underlying device hard header.
Use READ_ONCE() to read dev->hard_header_len and dev->needed_headroom as
they can be updated concurrently under RTNL (e.g. in
vlan_transfer_features()) while vlan_dev_hard_header() runs locklessly on
the transmit path. Also avoid LL_RESERVED_SPACE(dev) here so that the
extra HH_DATA_MOD alignment padding does not trigger unnecessary
pskb_expand_head() reallocations on inner stacked VLAN devices after the
outer VLAN header has been pushed. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: DQO: reject TSO packets with an out of range MSS
gve_prep_tso() notes that the device requires the MSS to be <= 9728,
but does not enforce it, assuming the 9K MTU enforced by the hypervisor
and the 64KB limit on TSO sizes are enough.
This does not hold for packets that were not generated locally.
A guest behind a tap, or any packet socket user, can provide an
arbitrary gso_size in virtio_net_hdr. Layer 2 forwarding does not check
the MTU for GSO packets (is_skb_forwardable()), and gso_features_check()
only bounds skb->len and gso_segs, never gso_size.
Such a packet reaches gve_tx_fill_tso_ctx_desc(), which puts gso_size
into the mss field of the TSO context descriptor. This field is 14 bits
wide, so a gso_size of 16384 is silently turned into an MSS of zero.
Drop these packets from gve_prep_tso(), and make sure that
gve_features_check_dqo() leaves their GSO bits alone: skb_segment()
splits at gso_size regardless of the MTU, so falling back to software
segmentation would give the device non TSO packets bigger than the
9728 bytes it supports.
Note that the device can still be given oversized non TSO packets when
the stack segments in software for other reasons, for instance after
TSO has been disabled with ethtool. This is a generic issue, because
the MTU check is skipped for GSO packets in the forwarding path, and
is addressed separately. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix UAF on lgr list traversal in smcr_port_err()
smcr_port_err() traverses smc_lgr_list.list without holding
smc_lgr_list.lock, allowing a concurrent smc_lgr_terminate_sched()
to free an lgr while it is still being dereferenced.
Hold smc_lgr_list.lock across the traversal. Update
smc_ib_gid_check() to call smcr_port_err() after releasing the lock. |
| In the Linux kernel, the following vulnerability has been resolved:
net/rds: size a connection's path set by the transport it ends up with
__rds_conn_create() computes npaths from the caller's transport before
it decides whether a connection to one of the host's own addresses is
to be handled by the loopback transport instead. That substitution is
what an RDS/TCP socket sending to a local address gets, and after it
the path init loop still runs for the TCP transport's RDS_MPATH_WORKERS
paths and allocates an ordered workqueue for each, while
rds_loop_conn_alloc() only ever provides transport data for path 0.
rds_conn_destroy() sizes its teardown from c_trans, by then the
loopback transport, so it visits path 0 only - and
rds_conn_path_destroy() would skip the other paths anyway, since it
returns before destroy_workqueue() for a path without transport data.
kfree(c_path) then drops the last pointers to seven workqueues. That
repeats for every such connection, on every netns teardown or module
unload, and every distinct local destination address is a separate
connection.
Recompute npaths once the transport is final, so that creation and
destruction agree on the set of paths. The c_path array stays sized
for the caller's transport; the unused entries are freed with it. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phylink: record the PHY only once bringup cannot fail
phylink_bringup_phy() stores the PHY in pl->phydev before its last
fallible step: on a MAC whose phylink ops implement LPI,
phy_eee_rx_clock_stop() can fail with a real MDIO error. The callers
unwind with phy_detach(), which knows nothing about pl->phydev, so a
pointer to a PHY that is no longer attached outlives the failed
connect.
What that costs depends on how the caller got here.
phylink_connect_phy() goes through phylink_attach_phy(), which refuses
to attach while pl->phydev is set, turning a transient MDIO error into
a permanent -EBUSY. The SFP path is worse than that: sfp_sm_probe_phy()
answers the failure with phy_device_remove() and phy_device_free(), and
it assigns sfp->mod_phy only past that error return, so nothing clears
pl->phydev and it is left pointing at a freed phy_device that
phylink_resolve() and the ethtool helpers go on reading.
phylink_fwnode_phy_connect() has no such check, so a later connect
overwrites the stale pointer and hides the problem. A disconnect does
not: phylink_disconnect_phy() hands that pointer to phy_disconnect(),
and the second phy_detach() on the same PHY drops references the first
one already released.
Found while making a DSA port survive a PHY whose driver arrives after
the switch probes: keeping the port across a failed connect and
retrying is what makes this window reachable.
Publish the pointer after the last call that can fail instead of
unwinding it afterwards. Nothing between the two points reads
pl->phydev, and the registration that follows cannot fail:
phy_request_interrupt() falls back to polling on its own. The PHY-side
state keeps the order it had, so no MDIO operation moves relative to
another. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: mt7530: leave the MDIO IRQ mappings to regmap-irq
mt7530_remove_common() disposes the per-PHY interrupt mappings from
.remove, but the regmap-irq chip that owns the domain is devm-registered,
so its parent interrupt is only freed once .remove has returned. The
switch's own regmap-irq thread can therefore still dispatch on a mapping
that is already gone: irq_find_mapping() returns 0, irq_to_desc() returns
NULL and handle_nested_irq() locks desc->lock without checking it. The
attached PHYs have not given those interrupts back yet either, which the
kernel warns about a moment before the fault.
regmap_del_irq_chip() disposes the same mappings itself, after freeing the
parent interrupt and before removing the domain, so there is nothing left
for the driver to do here. Until it runs the descriptors stay alive, and a
late dispatch on one of them is harmless: dsa_unregister_switch() has freed
the PHY handlers by then, so handle_nested_irq() finds no action and
returns. |
