| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: sr9700: include receive overhead in the length check
The receive fixup subtracts the Ethernet CRC from the reported packet
length, but compares that payload length against the whole remaining
receive buffer. The following copy starts after the three-byte header,
and the cursor advance consumes both that header and the four-byte CRC.
Require the payload to fit after SR_RX_OVERHEAD before copying it or
advancing to the next packet. The loop already ensures that the
remaining buffer is larger than the overhead, so the subtraction is
safe.
The issue was found by our static-analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: Prevent rt6_insert_exception() for dying fib6_info.
Before the cited commit, fib6_nh_flush_exceptions() always set
from->exception_bucket_flushed = 1 under rt6_exception_lock to
prevent rt6_insert_exception() from inserting a new exception
for a dying fib6_info.
The flag was replaced with the FIB6_EXCEPTION_BUCKET_FLUSHED
bit stored in nh->rt6i_exception_bucket.
The problem is that now the bit is only set when the bucket
is not NULL and fib6_nh_flush_exceptions() is called from
fib6_nh_release() after fib6_ref has already reached zero.
If rt6_insert_exception() is called while the target fib6_info
is being removed via fib6_purge_rt(), a new exception could be
created successfully because rt6_flush_exceptions() no longer
sets the bit.
This creates a reference cycle between the fib6_info and the
exception route, leaking the fib6_info, its nexthop device,
and all per-CPU routes in fib6_nh->rt6i_pcpu, which stalls netdev
unregistration.
[ 34.680602] unregister_netdevice: waiting for gre6 to become free. Usage count = 68
[ 44.920675] unregister_netdevice: waiting for gre6 to become free. Usage count = 68
[ 55.176582] unregister_netdevice: waiting for gre6 to become free. Usage count = 68
Let's call fib6_drop_pcpu_from() before rt6_flush_exceptions(),
to set fib6_destroying before rt6_exception_lock, and check
f6i->fib6_destroying in rt6_insert_exception().
Note that FIB6_EXCEPTION_BUCKET_FLUSHED logic is dead and
we can clean it up in net-next. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject non-negative offsets in stack_slot_obj_get_spi()
bpf_get_spi() computes (-off - 1) / BPF_REG_SIZE using C division,
which truncates toward zero. For off == 0, this produces spi 0, the
same index used by the valid stack slot at fp-8.
stack_slot_obj_get_spi() currently checks alignment and the resulting
spi bounds, but does not reject the non-negative offset itself. It can
therefore validate a PTR_TO_STACK register holding fp+0 against an
iterator stored at fp-8 even though the runtime receives the actual fp+0
pointer. An effectful iterator kfunc can then interpret memory outside
the BPF stack as iterator state.
Reject non-negative offsets before converting the offset to an spi. All
valid stack objects begin at a negative offset from the frame pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: Reject short EA=0 frames in rfcomm_recv_frame()
While rfcomm_recv_frame() verifies that skb->len is at least
sizeof(*hdr) + 1 (4 bytes: 3-byte header + 1-byte FCS), an RFCOMM frame
with an extended 2-byte length field (!__test_ea(hdr->len)) has a 4-byte
header plus a 1-byte FCS (5 bytes minimum, sizeof(*hdr) + 2).
When a 4-byte RFCOMM frame with EA == 0 arrives:
1. The initial skb->len < sizeof(*hdr) + 1 check passes (4 < 4 is false).
2. Trimming the FCS byte decrements skb->len to 3.
3. If __check_fcs() succeeds, skb_pull(skb, 4) fails (4 > 3) and returns
NULL without advancing skb->data.
4. Because the return value of skb_pull() is ignored, the un-pulled
3-byte struct rfcomm_hdr remains at skb->data and is either queued as
application payload via rfcomm_recv_data() or parsed as a multiplexer
control command via rfcomm_recv_mcc() on DLCI 0.
Fix this by extending the length check in rfcomm_recv_frame() to also
require skb->len >= sizeof(*hdr) + 2 when !__test_ea(hdr->len). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: bnep: fix out-of-bounds reads on short RX/TX frames and control fallthrough
Fix multiple out-of-bounds reads in Bluetooth BNEP frame processing:
1. In bnep_rx_frame() and bnep_ctrl_frame() (net/bluetooth/bnep/core.c),
use pskb_may_pull() to verify the BNEP header, control type byte,
filter count, and extension headers exist before reading them, and
return 0 after handling BNEP_CONTROL instead of falling through to
Ethernet frame submission when no extension headers follow.
2. In bnep_net_xmit() (net/bluetooth/bnep/netdev.c), verify skb->len >=
ETH_HLEN with pskb_may_pull() before reading the 14-byte Ethernet
header to prevent an out-of-bounds heap read and infoleak on short
AF_PACKET TX frames. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: replace bind when clearing stale local source
The UDP output fallback clears bind->local in place when the remembered
source address is no longer usable. The bind is RCU-published and read
locklessly by concurrent TX, so an IPv6 reader can observe a torn
address.
Retry the route lookup with source address autoselection without
modifying the bind. After a successful lookup, revalidate the bind and
route key under peer->lock, reset the dst cache, and best-effort publish
a replacement bind with a wildcard local address.
Do not cache the resolved dst when clearing the local source. Replacing
the source invalidates all per-CPU cache entries, while
dst_cache_set_ip4 and dst_cache_set_ip6 update only the current CPU
slot. The current packet can still use the resolved route; if bind
allocation fails, a later cache miss retries the repair. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: release the GEM object on virtio_gpu_vram_create() errors
virtio_gpu_vram_create() frees the object with a bare kfree(vram) on
both error paths after drm_gem_private_object_init() has run, and on the
second one after drm_gem_create_mmap_offset() has linked obj->vma_node
into the device's VMA offset manager. The freed object stays in that
interval tree, so a later lookup or insertion walks freed memory, and
the dma_resv and gpuva lock are never destroyed.
Call drm_gem_object_release() before kfree() on both paths. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: fix object leak in virtio_gpu_resource_create_ioctl()
virtio_gpu_resource_create_ioctl() calls drm_gem_object_release() on the
drm_gem_handle_create() error path instead of dropping the reference it
owns, so obj->funcs->free() never runs and the virtio_gpu_object, its
pages and sg table, the resource id and the host-side resource are
leaked.
Use drm_gem_object_put() instead. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: discard post-EOF pagecache when extending a file via zero range
smb3_zero_range() removed the pagecache only for the range being zeroed,
so when it extends the file the folio straddling the old EOF - which may
hold data dirtied past EOF through an mmap - was never dropped and became
visible as file content once the file was extended.
Lower the discard boundary to the smaller of the zero-range offset and the
old EOF. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: fix object leak when drm_gem_handle_create() fails
virtio_gpu_gem_create() owns the reference taken by
virtio_gpu_object_create(). On the drm_gem_handle_create() error path it
calls drm_gem_object_release() instead of dropping that reference.
drm_gem_object_release() is the inverse of drm_gem_object_init() and does
not touch the reference count or call obj->funcs->free(), so it is only
correct as the last step of a destructor, as in
virtio_gpu_cleanup_object(). Using it here leaves the bo at refcount 1
with no remaining reference, so virtio_gpu_free_object() never runs and
the shmem pages, sg table and virtio_gpu_object are leaked. Since
virtio_gpu_object_create() has already set bo->created,
VIRTIO_GPU_CMD_RESOURCE_UNREF is not queued either, leaking the host-side
resource and the resource id.
drm_gem_handle_create_tail() drops the handle reference on all of its
internal error paths, so the caller only has to drop its own. Use
drm_gem_object_put(), matching the success path below. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: catc: bound the RX packet length in catc_rx_done()
catc_rx_done() walks a multi-packet URB, reading a two-byte length from
each packet header. Its bound, pkt_len > urb->actual_length, ignores the
header offset and compares against the whole transfer rather than the
bytes left from pkt_start, so a crafted packet header makes
skb_copy_to_linear_data() read past the buffer.
A length below ETH_HLEN is also accepted, including zero, and
eth_type_trans() then reads a MAC header from the uninitialised tailroom
of a shorter skb. The is_f5u011 branch takes its length straight from
the transfer, so a zero-length URB reaches the same path.
Track the bytes remaining from the current packet, and reject a header
that does not fit, a length past what is left, and a length below an
Ethernet header.
A transfer shorter than an Ethernet header, including a zero-length one,
previously became a runt skb passed to netif_rx() and counted as
received; it is now counted in rx_length_errors and ends the walk. |
| In the Linux kernel, the following vulnerability has been resolved:
eth: fbnic: Handle maximum standalone channels
Standalone channels use one NAPI vector for each Tx and Rx queue.
fbnic's allocation path excludes FBNIC_MAX_TXQS from that layout. A
64-Tx/64-Rx configuration therefore records 128 vectors but allocates
only 64, leaving NULL entries that resource setup dereferences.
Include the maximum vector count in standalone allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk_eth_soc: unregister net_devices in case of probe failure
If register_netdev() fails for one of the MTK_MAX_DEVS devices in
mtk_probe(), the error path jumps to err_deinit_ppe, skipping
mtk_unreg_dev(). The previously registered net_devices are then freed by
mtk_free_dev() while still in NETREG_REGISTERED state, hitting the
BUG_ON(dev->reg_state != NETREG_UNREGISTERED).
Route the register_netdev() failure to err_unreg_netdev so the net_devices
registered so far are properly unregistered before being freed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: gue: reject invalid REMCSUM offsets
The REMCSUM option carries an absolute checksum start and checksum field
offset. gue_remcsum() passes them to skb_remcsum_process(), whose
partial path stores offset - start in the u16 skb->csum_offset variable.
If offset is less than start, this underflows.
A forwarded packet can retain CHECKSUM_PARTIAL and reach a NETIF_F_HW_CSUM
driver which trusts the metadata, leading skb_copy_and_csum_dev() to write
two bytes about 64 KiB beyond the destination buffer.
Reject reversed tuples in validate_gue_flags(), after the existing length
validation, so all GUE parsers enforce the ordering in one place. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_ct: don't WARN on benign flow_offload_alloc() failure
flow_offload_alloc() returns NULL when the conntrack entry is dying
(e.g. raced with a conntrack flush) or when the GFP_ATOMIC allocation
fails; both are expected under load and neither is a kernel bug. This
path runs from softirq on every committed packet, so with
panic_on_warn=1 an unprivileged user can panic the box just by racing
a conntrack flush against a `tc ... action ct commit` classifier.
Reproduced with a custom repro under QEMU: a small, fixed set of UDP
flows through `tc filter ... action ct commit` on lo, raced against
threads flooding bare ctnetlink CT_DELETE (flush) requests. Hits
WARNING: net/sched/act_ct.c:437 (tcf_ct_flow_table_add(), inlined
into tcf_ct_act() in this build) within ~15s on the unpatched kernel;
same setup is clean on the patched kernel. The fix itself is
behavior-preserving: both branches already did `goto err_alloc`
before and after, only the WARN is removed. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Make post-verification instruction rewrites killable
After do_check() returns, the verifier runs several instruction rewrite
passes. Some of them patch or remove one instruction at a time. Each
operation moves the remaining instruction and auxiliary-data arrays and
adjusts all branch offsets, making the overall work quadratic in the
program length.
A privileged loader can submit 131072 unconditional jumps by zero followed
by a valid return. Verification finishes quickly, but bpf_opt_remove_nops()
then spends a long time removing each jump separately. Since this
post-verification work neither checks for signals nor reschedules, a pending
SIGKILL cannot terminate the task until the rewrite finishes.
Make bpf_patch_insn_data() and verifier_remove_insns() common cancellation
and rescheduling points. These helpers run from BPF_PROG_LOAD process
context, and bpf_patch_insn_data() can already sleep while reallocating
auxiliary data.
Report interrupted constant blinding as -EINTR and propagate it through
both JIT paths, including kernels that permit interpreter fallback.
Other blinding failures retain the existing fallback behavior.
This does not reduce the quadratic cost of the rewrite passes, but it makes
the work preemptible and allows a killed loader to be torn down promptly. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_u32: fix manual hash table handle IDR aliasing
A u32 hash table created with an explicit handle ('tc filter add ...
handle 801: u32 divisor N') keys its IDR entry on the raw handle, while
the destroy paths free it under handle2id(handle). The two key domains
disagree for handles in the 0x800..0xFFF htid range:
handle2id() folds them back into the auto-allocated id space (1..0x7FF).
A manual table therefore leaves its raw-keyed IDR entry unreachable on
delete (a permanent leak), and its delete can drop the idr entry of an
unrelated live auto table. A later auto allocation can then hand out a
handle that aliases the live manual table; u32_lookup_ht() first-match
routes lookups and TCA_U32_LINK for that htid to the wrong table.
Key the divisor-path alloc on handle2id(handle) so allocation and
removal share one key domain. A manual handle that maps onto an id
already in use is rejected with -ENOSPC, and auto allocation skips ids
held by live manual tables.
Conditions to recreate:
ip link add test0 type dummy
tc qdisc add dev test0 clsact
tc filter add dev test0 ingress protocol ip pref 1 \
handle 801: u32 divisor 16
tc filter add dev test0 ingress protocol ip pref 2 u32 divisor 16
tc -d filter show dev test0 ingress | grep 'fh 801:'
# unpatched: two live tables with handle 0x80100000 (the pref 2 root
# hnode is auto-allocated id 1); patched: the auto hnode takes id 2.
Also tested with a poc with a live u32 table on the block, add/delete a manual
table 'handle 901: u32 divisor 1' twice; unpatched, the re-add fails with
-ENOSPC because the raw key leaked on the first delete. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: mgmt: Dequeue pending mesh_send_sync entries on cancel
In send_cancel(), pending mesh_tx objects are removed from the
hdev->mesh_pending list and freed via mesh_send_complete(). However, if
a mesh transmission was already queued onto hdev->cmd_sync_work_list via
mesh_next(), the queued entry retains a raw pointer to mesh_tx.
When hci_cmd_sync_work later processes the entry, it attempts to execute
mesh_send_sync and its destroy callback mesh_send_start_complete using
the already freed mesh_tx pointer, leading to a use-after-free.
Fix this by invoking hci_cmd_sync_dequeue() for mesh_send_sync on the
target mesh_tx before completing it. If the entry is found and dequeued,
its destroy callback will complete and free the object; otherwise,
mesh_send_complete() is called directly.
Additionally, ensure the transmission queue advances after cancellation
or errors. In mesh_send_start_complete(), call mesh_next() on error
unless err is -ECANCELED, because hci_cmd_sync_dequeue() holds
hdev->cmd_sync_work_lock and calling mesh_next() synchronously would
deadlock. Instead, advance the queue in send_cancel() once the lock is
released and if no transmission is in progress. |
| Integer underflow (wrap or wraparound) in DNS Server allows an unauthorized attacker to execute code over a network. |
| Relative path traversal in Windows Shell allows an authorized attacker to elevate privileges locally. |
